Additional information
| Weight | 77 g |
|---|---|
| Dimensions | 125 × 27 × 27 mm |
Sold
Barrel Weight 19.91mm
£34.99
Genuine Feinwerkbau P70FT barrel weight, may fit other rifles, too (please check the diameter of your barrel before ordering).
With an extra M6 hole for a windicator.
Aluminum, 77g and the inside diameter is 19.91mm
Out of stock
Only logged in customers who have purchased this product may leave a review.
You may also like…
Sniper Barrel Weight
Flat barrel weight for Feinwerkbau / Anschütz rifles. The same weight (79 g) as the original FWB aluminium barrel weight but allows using longer cylinders – it is only 1 mm thick below and above the barrel. Laser sintered Nylon, with stainless steel grub screw. The M6 threaded holes at the bottom allow you to add up to 10 grub screws to fine tune the total weight and its distribution. The barrel weight aligns itself to the dovetail at the end of FWB barrel. It clamps onto the barrel only with Nylon parts so doesn’t scratch the barrel surface.
New: available also for Daystate Griffin, everything the same as above.
New version: Similar for Steyr but longer, with three air stripper plates as well. ComBrella can’t be connected to this model.
Intimidate your opponents with a rifle that looks like a .50 cal sniper gun! ;-)
Now you can have it with the ComBrella shade that can hold a Combro chrony and connects with a bayonet to the barrel weight, keeping the chrony on its place, aligned with the barrel and protecting it from the sunlight.
It can be ordered with a built-in folding windicator, too.
Sold
£29.99
Out of stock
Barrel Weight 17.22mm
Genuine Walther LGR barrel weight, may fit other rifles, too (please check the diameter of your barrel before ordering).
Steel, 271g and the inside diameter is 17.22mm.
Related Products
FWB Loading Port Handle
Comfortable handle for the loading port of Feinwerkbau P70 rifles. Replaces the original ugly white handle with a much better one. In R/H and L/H versions, made of laser sintered Nylon with stainless steel screws.
With this, you can close the loading port by rotating the handle easily by the two rounded ends, instead of pushing it down with a quite big force.
The handle is combined with an automated safety mark: when the loading port is open, a piece of flexible cable tie blocks your trigger finger, but goes out of the way when the port is closed.
Save £19.00!
Original price was: £34.90.£15.90Current price is: £15.90.
Add to basket
Centra Vertical 2.4mm
For M18 diopter tunnel
Sold
Original price was: £89.99.£64.99Current price is: £64.99.
Select options
This product has multiple variants. The options may be chosen on the product page
GAPacity Sidewheel + Free Pointer
This product has been discontinued. Check out the new design, the Composite series:
- Composite Parallax Wheels: 125mm and 150mm DualCore (round centered/excentric), 225mm effective diameter comma wheel.
- Composite Click Turret: 54 mm oversized turret, resettable without tool, wit or without bottoming ring.
- Composite Zoom Lever: stylish and handy zoom lever.
- All three in a bundle on a reduced price: Composite Scope Kit
Sold
Original price was: £14.99.£9.99Current price is: £9.99.
Select options
This product has multiple variants. The options may be chosen on the product page
EasyPin Pointer
Simple and lightweight scope pointer. Fits to all 1″ / 30 mm / 34 mm scope tubes, and needs only 10×10 mm space in width and length as seen on the picture.
For 36mm and 40mm tube diameters see EasyPin Extra
For click turrets with a custom made cap, or for sidewheels. With stainless steel screws and steel pin. If you need a longer or shaped pin, you can simply replace the original pin with any <1mm wire. Find out which pointer suits you best: Scope Pointer Comparison Table
NEW: there is an advanced version of this pointer available, too, with adjustable pin angle and also for 36mm and 40mm scope tubes: EasyPin Extra Scope Pointer
THE Field Target Shooting Glove
The world’s first dedicated Field Target glove, designed specially for FT / HFT shooting, by a Field Target shooter. This is a high quality heavy target glove, for the leading hand (left hand for a right-handed shooter and vica versa), padded and with Top Grip on most surfaces.
Three fingers are half length so the shooter can easily rangefind and click the scope. Thick but quite flexible Top Grip pads on every surface where needed for every shooting position and with elastic wrist band.
Available sizes: XS, S, M, L, XL – please check the sizing guide below for your glove.
Available colours: Black, Blue, Red, Green (new!!!)
Sorry but only Black for L/H shooters)
WonderBar adjustable spacers (in pair)
A pair of two specially formed adjustable spacers that can connect to each other in four different heights:
Useful for spacing butt-hooks, hamsters and other rifle parts.
Prices stand for a pair of spacers.
LAST ONES!
Four Seasons FT Light Gloves
The world’s first lightweight Field Target gloves, designed specially for FT / HFT shooting, by a Field Target shooter. These are light but very useful gloves, for the firing hand but also for the leading hand if you don’t like massive target gloves. The prices are per pairs. See the product description at the bottom of this page for more information.
Available sizes: XS, S, M, L, XL – see the glove sizing guide below.
Available colours: Black, Blue, Red.
Last ones, stock is running out soon…
WFTF Target Checker
The official WFTF Target Checker (designed by Brian Samson, public domain, printed under the Creative Commons CC0 licence).
“The device is designed to give an equivalent impact force to an airgun pellet hitting the paddle of a target at 5.5 ft/lbs energy (7 Joules). To mimic the effect of a target being shot at with a WFTF legal air rifle at 55 yards.”
Fully assembled and ready to use. High quality 3D-printed PLA/PHA in black and orange colours, stainless steel bolts/nuts.
MK2 2018– Brian’s original design
MK3 2019 – Smaller improvements like easily adjustable depth gauge, wrist strap, killzone diameter checkers etc., see below for more details.
MK4 2020 – Further improvements to resolve all issues of the original design. Re-designed internal parts, spring tension can be fine-tuned with a hex key, free travel length of the probe doubled.
MK4.1 2023 – Further improvements, small modifications, safer trigger etc.
MK4.2 2024 – Morer improvements, re-designed trigger, spring guide etc.
Available colours: Dutch Orange, Ultra Marine Blue, Traffic Red, Leaf Green, Intense Green, Fluorescent Pink, Signal Yellow, Shining Silver and Sky Blue, all with black sides.
Detailed instructions manual (by Scott Hull): download PDF
Reviews
There are no reviews yet.