Additional information
| Weight | 79 g |
|---|---|
| Dimensions | 156 × 50 × 22 mm |
| RIFLE | FWB / Anschütz, Steyr, Daystate Griffin, Bespoke design |
Sniper Barrel Weight
Price range: £49.90 through £69.90
Flat barrel weight for Feinwerkbau / Anschütz rifles. The same weight (79 g) as the original FWB aluminium barrel weight but allows using longer cylinders – it is only 1 mm thick below and above the barrel. Laser sintered Nylon, with stainless steel grub screw that doesn’t touches the barrel directly so it is safe for the chromed surface. The M6 threaded holes at the bottom allow you to add up to 10 grub screws to fine tune the total weight and its distribution. The barrel weight aligns itself to the dovetail at the end of FWB barrel. It clamps onto the barrel only with Nylon parts so doesn’t scratch the barrel surface.
New: available also for Daystate Griffin, everything the same as above.
New version: for Steyr, this is similar but longer, with three air stripper plates as well. ComBrella can’t be connected to this model.
Intimidate your opponents with a rifle that looks like a .50 cal sniper gun! ;-)
Now you can have it with the ComBrella shade that can hold a Combro chrony and connects with a bayonet to the barrel weight, keeping the chrony on its place, aligned with the barrel and protecting it from the sunlight.
It can be ordered with a built-in folding windicator, too.
Only logged in customers who have purchased this product may leave a review.
You may also like…
FWB Anti-POI-Shift Kit
The FWB Anti-POI-Shift Kit stands of two laser sintered Nylon parts, they look the same but they’re a bit different inside:
- One of them replaces the original A-clamp and holds only the cylinder and protects the barrel from accidental kicks but lets it free float.
- The other one goes to the joint of the air cylinder and the reg. It can be fixed onto the barrel by two symmetrical grub screws that push small Nylon parts to the barrel and thus don’t scratch its surface.
With stainless steel screws, all secured against falling out. Easy mounting (you’ll have to drill only a 5 mm hole).
For a perfect solution please see also: FWB Anti-POI-Shift Rail
Sold
£34.99
Out of stock
Barrel Weight 19.91mm
Genuine Feinwerkbau P70FT barrel weight, may fit other rifles, too (please check the diameter of your barrel before ordering).
With an extra M6 hole for a windicator.
Aluminum, 77g and the inside diameter is 19.91mm
FWB Loading Port Handle
Comfortable handle for the loading port of Feinwerkbau P70 rifles. Replaces the original ugly white handle with a much better one. In R/H and L/H versions, made of laser sintered Nylon with stainless steel screws.
With this, you can close the loading port by rotating the handle easily by the two rounded ends, instead of pushing it down with a quite big force.
The handle is combined with an automated safety mark: when the loading port is open, a piece of flexible cable tie blocks your trigger finger, but goes out of the way when the port is closed.
Related Products
InkWell for Pellet Sizer
Pellet collector for pellet sizers. Please note that the pellet sizer is NOT included, it has to be bought separately from UK Neil or other manufacturers.
Can collect about 300 pellets. If you take the bottom plate off, will fit firmly into a tin so you can size the pellets directly into the tin.
High quality laser sintered Nylon (black dyed and polished), stainless steel screws.
Some words from the product’s first user: “A great product. Very light. The UK Neil sizer slides into the ink well holder for a perfectly snug fit. Enables speedy sizing and any pellets dropped fall onto the top of the well. This stops the odd dropped pellet falling into your sized pellets by mistake. Perfect.“
And a short review on Youtube from another customer: https://youtu.be/DlvtUxTHPSs?t=343
Anti-POI-Shift Rail (for Feinwerkbau / Anschütz)
High quality scope rail for Feinwerkbau or Anschütz PCP rifles. Designed especially to work together with my FWB Anti-POI-Shift Kit, using these products together eliminates the POI-shifts on Feinwerkbau Alutec stocks. I’ve been using the same solution on my rifle, and the last time I zeroed my rifle was in 2012, need to tell anything more?!?
Made of aircraft grade aluminium alloy, black anodised with stainless steel bolts or silver anodised with black bolts. Elevation 35 mm, reproduces the same dovetail on the top as the rifle’s original dovetail. The in-built slope is 0.71% = 24.4 MOA so any simple mount ring will do without shimming.
For a perfect solution please see also: FWB Anti-POI-Shift Kit.
Sold
£89.90
Select options
This product has multiple variants. The options may be chosen on the product page
JOPA Folding Bipod
Folding bipod, made of quality materials. Body: black or silver anodised aluminium alloy, legs: 5mm stainless steel with 20mm black plastic balls.
Long legs (12.5cm = 5″ between the ground and the rifle’s stock)
Fits to all rifles with standard accessory rail or similar (AirArms, Anschütz, Walther, Steyr, Feinwerkbau, Hämmerli etc.)
Sorry this product is discontinued but now I have two black ex demo pieces available, been used for a couple of competitions, photo sessions and as a demo when selling other ones on international competitions. In excellent condition, only with a few marks from being mounted onto a rifle.
These are the very last ones of the JOPA series.
Check out my new Atlas Extra Wide FT Bipod
FWB Stock Middle Parts
Replacement elements for the FWB P70 Alutec stock, giving new features to the rifle:
- Fully adjustable offset grip
- Elevating the rear part by 50 mm
- Saving 250 g weight
Also the original grip can be used (but without the offset feature). The parts are made of laser sintered Nylon, lightweight but very strong, I personally have tested this kit on my rifle. The new design elevates the cheek piece part so it fits better to high FT scopes. The grip is fully adjustable, and the offset can be set between 7.5 and 22.5 mm.
Right handed, used but in “as new” condition, with some very small usage marks. Can be bought with a ball grip and/or with a grey anatomic grip.
In order to use this kit, you have to cut your original stock, and drill 3 new holes onto it, I’ll attach the technical drawings of all these modifications of course.
I can offer a full FWB collection, please contact me for a discounted price if you are interested in the following products together:
- This kit
- FWB Anti-POI-Shift Kit (optionally with FWB Anti-POI-Shift Rail)
- FWB Loading Port Handle
- FlexiPoint Offset Trigger for FWB
- FlexiPoint Additional Trigger Blade
Scorpion Base Plates
Custom base plates and adapters for the Scorpion Field Target Hook, to fit it to different rifle stocks
Other spare parts are available here: Scorpion FT Hook Extras.
THE Field Target Shooting Glove
The world’s first dedicated Field Target glove, designed specially for FT / HFT shooting, by a Field Target shooter. This is a high quality heavy target glove, for the leading hand (left hand for a right-handed shooter and vica versa), padded and with Top Grip on most surfaces.
Three fingers are half length so the shooter can easily rangefind and click the scope. Thick but quite flexible Top Grip pads on every surface where needed for every shooting position and with elastic wrist band.
Available sizes: XS, S, M, L, XL – please check the sizing guide below for your glove.
Available colours: Black, Blue, Red, Green (new!!!)
Sorry but only Black for L/H shooters)
PinPoint v.2 Trigger
Precision trigger for the following rifles:
- Anschütz
- AirArms Pro-Target / EV-2 / FTP-900
- Daystate Adjustable Trigger
- Feinwerkbau (all models)
- FX Impact
- Hämmerli AR-20
- Steyr LG-100/110
- Suhl 150
- Thomas
- Walther (all models)
The trigger can be ordered with a wide variety of different trigger blades on a bundle price (they can be ordered later on full price here: FlexiPoint spare blades).
Offset 0-10mm to both sides. If you need a trigger with more offset (up to 46 mm!) and much more adjustment options, check out my Flexipoint trigger.
WFTF Target Checker
The official WFTF Target Checker (designed by Brian Samson, public domain, printed under the Creative Commons CC0 licence).
“The device is designed to give an equivalent impact force to an airgun pellet hitting the paddle of a target at 5.5 ft/lbs energy (7 Joules). To mimic the effect of a target being shot at with a WFTF legal air rifle at 55 yards.”
Fully assembled and ready to use. High quality 3D-printed PLA/PHA in black and orange colours, stainless steel bolts/nuts.
MK2 2018– Brian’s original design
MK3 2019 – Smaller improvements like easily adjustable depth gauge, wrist strap, killzone diameter checkers etc., see below for more details.
MK4 2020 – Further improvements to resolve all issues of the original design. Re-designed internal parts, spring tension can be fine-tuned with a hex key, free travel length of the probe doubled.
MK4.1 2023 – Further improvements, small modifications, safer trigger etc.
MK4.2 2024 – Morer improvements, re-designed trigger, spring guide etc.
Available colours: Dutch Orange, Ultra Marine Blue, Traffic Red, Leaf Green, Intense Green, Fluorescent Pink, Signal Yellow, Shining Silver and Sky Blue, all with black sides.
Detailed instructions manual (by Scott Hull): download PDF
Reviews
There are no reviews yet.